| 01 |
Passed |
| 02 |
Failed |
| 03 |
Not accessible |
| A04 |
Job not ready for inspection |
| A05 |
No address posted |
| A06 |
Wrong contractor listed |
| A07 |
Missing required inspections |
| A08 |
Need additional permits |
| A09 |
Call Inspector |
| A10 |
Approved plans not on jobsite |
| A12 |
Approved plan error |
| A13 |
Need ladder |
| A14 |
Defect not previously listed |
| A16 |
Permanent access to roof missing or incorrect |
| B01 |
Building or stairs not safe |
| B02 |
Building energy code requirements not met |
| C01 |
Combustion air missing |
| C02 |
Combustion air not installed per code |
| C03 |
Combustible material in return plenum |
| C04 |
Commercial grease hood not installed correctly |
| C05 |
Commercial grease duct not installed correctly |
| C06 |
Commercial grease hood fan not installed correctly |
| D01 |
Duct material incorrect |
| D02 |
Duct clearances incorrect |
| D03 |
Duct support incorrect |
| D04 |
Duct installation incorrect |
| D05 |
Ducts or boots not sealed |
| D06 |
Duct damaged or restricted |
| D07 |
Duct insulation incorrect |
| D08 |
Duct for makeup missing or incorrect |
| D09 |
Duct for bathroom exhaust missing or incorrect |
| D10 |
Duct for range exhaust system missing or incorrect |
| D11 |
Dryer vent missing or incorrect |
| D12 |
Duct for exhaust not per code |
| E01 |
Equipment protection needed |
| E02 |
Missing equipment |
| E03 |
Equipment not supported properly |
| E04 |
Equipment access incorrect |
| E05 |
Equipment clearance incorrect |
| E06 |
Equipment platform or catwalk missing or incorrect |
| E07 |
Equipment not installed per manufacturer's instructions |
| E08 |
Equipment installation instructions not on jobsite |
| E09 |
Equipment not vented |
| E10 |
Equipment protection missing or incorrectly installed |
| E12 |
Equipment flue drain missing or incorrectly installed |
| F01 |
Flue clearances incorrect |
| F02 |
Flue materials incorrectly installed |
| F03 |
Flue not installed properly |
| F04 |
Flue not supported properly |
| F05 |
Flue not secure to equipment or draft hood |
| F06 |
Flue not terminated properly |
| F07 |
Flue liner for chimney missing or incorrectly installed |
| F08 |
Flue Chase missing or incorrect |
| F09 |
Furnace vent drain missing or incorrectly installed |
| F10 |
Flue insulation shield missing or incorrectly installed |
| G01 |
Gas pipe not complete |
| G02 |
Gas cutoff and or proper fittings missing |
| G03 |
Gas test not to code or bad gauge |
| G04 |
Gas pipe damaged or improperly installed |
| G05 |
Gas Piping material incorrect |
| G06 |
Gas Piping support not per code |
| G07 |
Gas Piping protection not per code |
| G08 |
Gas piping labels not per code |
| G09 |
Gas line regulator missing or incorrect |
| G10 |
Underground gas piping not per code |
| G11 |
Remove regulator for testing |
| G12 |
Plug future gas outlets |
| G13 |
Paint exposed gas lines |
| G14 |
Drip tee missing or incorrect |
| G15 |
Regulator test ports missing |
| G16 |
Missing suite number at gas meter |
| H01 |
Damage caused by others |
| M01 |
Filters missing |
| M02 |
Missing supply or return registers |
| M04 |
Fresh air intake clearance to exhaust not per code |
| M05 |
Missing fireplace mantle |
| M06 |
Mantle clearance incorrect |
| M07 |
Missing fireplace hood |
| P01 |
Primary or secondary drains missing or incorrect |
| P02 |
Pan drain missing or incorrect |
| P03 |
Pan for equipment missing or incorrectly installed |
| P04 |
Pan safety float switch missing |
| P05 |
Condensate pump missing or incorrect |
| P06 |
Missing insulation on refrigeration piping |
| S01 |
Fire or smoke damper installation incorrect or missing |
| S02 |
Smoke detector missing or incorrect |
| S03 |
Fire or smoke stopping incorrect |
| S04 |
Manual fan shutdown missing |
| S05 |
Missing fire damper access door |
| W01 |
Pipe insulation at water heater missing or incorrect |
| W02 |
Water heater draft hood not installed |
| W03 |
Water heater not level |
| W04 |
T & P drain missing or incorrect |
| W05 |
Water heater stand missing or incorrect installed |
| W06 |
Water heater protection missing or incorrect |
| Z96 |
Approval withheld for other trade requirements |
| Z97 |
Verify existing load calculation |
| Z98 |
Existing condition not code compliant |
| Z99 |
other or no defect code applies |